The BIOS in this sytem is not fully ACPI compliant

I'm needing a genuine "guru" to help resolve a serious problem. Hopefully
someone here is up for the challenge. The following is long but perhaps
necessary to provide information which would most likely be asked for
anyway. The system is just short of a year old and has been working
perfectly up until yesterday.

System Specs:
Windows Vista Ultimate and XP Home (dual-boot)
AMD Athlon 64 X2 4200+
Asus M2N-E
Mushkin PC2 5300 667 - 3 gigs
EVGA GeForce 7600 GT KO
Antec NS 430 Watt
WD 250 gig SATA II x2

Problem:
Most of the time when I bootup I get a BSOD with the following message:

I removed the CMOS battery and reset the BIOS with the mb jumper. No change.
I just now tried "Last known good configuration" for the second time today.
No change.

I following the insructions in a MSKB article,
http://support.microsoft.com/kb/831691, that dealt with this error that
recommended removing the "hiberfil.sys" file, but I wasn't able to delete
it. When I tried to delete it I got an error message saying "File not
found"??? But it is definitely there.

I wondered if the same anomalies I'm seeing in Vista also would be in XP.
So, I tried booting into XP (dual-boot) system and the bootup hung and the
bootscreen logo. So, I can't get into XP to find out. I then used Vista
BootPro 3.3 to restore a saved backup but no change. I pulled the mb battery
and reset the BIOS with the mb jumper, no change. I have run 2 memory
diagnostic tests both with no errors. I have run WD's "Data Lifeguard
Diagnostic" utility and all passed with flying colors. I have tried booting
into "Last known good configuration", but again, no change. And I decided to
restore a week-old True Image backup, using the Boot Disk, but clicking
"Next" on the first screen of the Restore feature, the system hung and I got
one loud, long beep. I had to hard reboot to escape. I've flashed the BIOS
with 3 different versions, no change. I've also tried System Restore with 3
different restore points

I booted with the Vista DVD and ran the Boot repair/check and no errors.
Also ran Vista/Microsoft RAM diagnostic even though memtest86 said no errors
and Microsoft's test was good too. I ran WD's "Data Lifeguard Diagnostic"
utility, both Quick and Advanced with no errors or problems. I removed the
last two "Hot Fixes", uninstalled Logitech Mouse drivers, disabled the
Sidebar, etc. No change.

The only real change I have made is to install a new Samsung 931c LCD
monitor. And, I even disconnected that and tried an old CRT monitor out of
desperation.... no change. I am running the latest Nvidia drivers v. 162.66
and reverted back to an earlier version 158.44 and no change.
Another very strange anomaly is after the system boots into Windows Vista,
if I click on the Start Orb to open the Start Menu, a very long line of "+"
symbols fills the field. After about 30 seconds the same Search results are
displayed above. I can use "Ctrl + a" to select all the "+" signs and delete
them which then reverts the Start Menu to the way it should be. These same
"+" signs will appear in the "Instant Search" box of Windows Explorer if I
open that first.

Hapkido wrote:
> I'm needing a genuine "guru" to help resolve a serious problem.
> Hopefully someone here is up for the challenge. The following is long
> but perhaps necessary to provide information which would most likely be
> asked for anyway. The system is just short of a year old and has been
> working perfectly up until yesterday.

My guess would be that your motherboard or processor (or possibly RAM)
has failed.
Probably motherboard. (There is little to go wrong with the RAM if it's
been working for a year and you're not overclocking it (too much)).

Alun Harford

Hapkido wrote:
> I'm needing a genuine "guru" to help resolve a serious problem.
> Hopefully someone here is up for the challenge. The following is long
> but perhaps necessary to provide information which would most likely be
> asked for anyway. The system is just short of a year old and has been
> working perfectly up until yesterday.
>
> System Specs:
> Windows Vista Ultimate and XP Home (dual-boot)
> AMD Athlon 64 X2 4200+
> Asus M2N-E
> Mushkin PC2 5300 667 - 3 gigs
> EVGA GeForce 7600 GT KO
> Antec NS 430 Watt
> WD 250 gig SATA II x2
>
> Problem:
> Most of the time when I bootup I get a BSOD with the following message:
>
>

Quote:

"The BIOS in this sytem is not fully ACPI compliant. Please > contact your sysem vendor for an updaed BIOS." > > STOP 0x000000A5 (0x00000011, 0x00000006, 0x00000000, 0x00000000)

> I removed the CMOS battery and reset the BIOS with the mb jumper. No
> change. I just now tried "Last known good configuration" for the second
> time today. No change.
>
> I following the insructions in a MSKB article,
> http://support.microsoft.com/kb/831691, that dealt with this error that
> recommended removing the "hiberfil.sys" file, but I wasn't able to
> delete it. When I tried to delete it I got an error message saying "File
> not found"??? But it is definitely there.
>
> I wondered if the same anomalies I'm seeing in Vista also would be in
> XP. So, I tried booting into XP (dual-boot) system and the bootup hung
> and the bootscreen logo. So, I can't get into XP to find out. I then
> used Vista BootPro 3.3 to restore a saved backup but no change. I pulled
> the mb battery and reset the BIOS with the mb jumper, no change. I have
> run 2 memory diagnostic tests both with no errors. I have run WD's "Data
> Lifeguard Diagnostic" utility and all passed with flying colors. I have
> tried booting into "Last known good configuration", but again, no
> change. And I decided to restore a week-old True Image backup, using the
> Boot Disk, but clicking "Next" on the first screen of the Restore
> feature, the system hung and I got one loud, long beep. I had to hard
> reboot to escape. I've flashed the BIOS with 3 different versions, no
> change. I've also tried System Restore with 3 different restore points
>
> I booted with the Vista DVD and ran the Boot repair/check and no errors.
> Also ran Vista/Microsoft RAM diagnostic even though memtest86 said no
> errors and Microsoft's test was good too. I ran WD's "Data Lifeguard
> Diagnostic" utility, both Quick and Advanced with no errors or problems.
> I removed the last two "Hot Fixes", uninstalled Logitech Mouse drivers,
> disabled the Sidebar, etc. No change.
>
> The only real change I have made is to install a new Samsung 931c LCD
> monitor. And, I even disconnected that and tried an old CRT monitor out
> of desperation.... no change. I am running the latest Nvidia drivers v.
> 162.66 and reverted back to an earlier version 158.44 and no change.
> Another very strange anomaly is after the system boots into Windows
> Vista, if I click on the Start Orb to open the Start Menu, a very long
> line of "+" symbols fills the field. After about 30 seconds the same
> Search results are displayed above. I can use "Ctrl + a" to select all
> the "+" signs and delete them which then reverts the Start Menu to the
> way it should be. These same "+" signs will appear in the "Instant
> Search" box of Windows Explorer if I open that first.
>


I have the same machine almost and it's been faultless - and since XP is
also having trouble it is unlikely a Vista problem or any OS problem.
That MS is power hungry IMHO judging by the heat coming off that big
heatsink tube and with the 7600 SLI card mine gets pretty warm.

I wonder if your 450 watt PSU is big enough and whether it's on the way
out. If this problem just recently started it may be worth a try. My
biggest machine has 1000 Watt

Where do you live? It's been damned hot in Iowa recently and if, like
me, you prefer to leave machines running than risk thermal shock by keep
turning them off then maybe a bigger PSU would work out a cheaper
diagnostic option.

Also we had a lot of thunderstorms and of course that brings with it
power glitches.

Have to triend turning off all power management features in your BIOS

As far as the + signs go, what happens when you open notepad, or an
other text editor, like word?. Do the +++++++'s begin to appear ther
also? That could be indicative of a bad keyboard/keyboard controller, i
which case you need to check motherboard drivers

If you're using a USB keyboard, try replacing that with a PS/2 base
keyboard, or if not possible, then enable Legacy USB support in you
BIOS also

--
dzomlij

___________________________________
Peter Alexander Dzomlij
Do you hear, huh? The Alpha and The Omega? Death and Rebirth? And a
you die, so shall I be Reborn...

Hi Hapkido--

I have multiple APBs out accross the US for "genuine gurus." Meanwhile..

That's a nice box you have. I admire your tenacity. You've reasonably
tried a lot of good options. I'm a bit disappointed that Acronis's tools
couldn't get you back.

Three things I'd try:

1) At F8, while you're tried one means of system restore (3 points) and LKG;
you should try system restore from every other safe mode @ F8 (Windows
Advanced Options Menu)

Think: I have 4 different ways to get back my XP at F8 and try 'em in order.
1) Safe Mode 2) Safe Mode with Cmd to Sys Restore which is simply a cmd
prompt in safe mode 3) Safe Mode with Neworking 4) LKG or Last Known Good
Configuration (I know you have tried LKG).

and 2) also put in that Vista DVD and *try System restore from the Recovery
link where you tried to run Startup Repair.

The link looks like this pic at the bottom here:
http://www.windowsvista.windowsreins...rtup/part1.htm

http://www.vistaclues.com/wp-content...r-computer.png


You might be thinking--"why the hell are those going to do any good when
I've already tried 3 restore points because after all--restore points are
restore points?" I understand the logic of that--but the reality is that
sometimes system restore from one safe mode or from Vista's recovery link
(the Win RE access to System Restore) just works.

3) I'd try a repair install with your Vista DVD. You do it the same way as
in XP:


***Repair Install Steps*** (can be used for Vista) MVP Doug Knox
http://www.microsoft.com/windowsxp/u...ps/doug92.mspx

Good luck,

CH



"Hapkido" <> wrote in message
news:...
> I'm needing a genuine "guru" to help resolve a serious problem. Hopefully
> someone here is up for the challenge. The following is long but perhaps
> necessary to provide information which would most likely be asked for
> anyway. The system is just short of a year old and has been working
> perfectly up until yesterday.
>
> System Specs:
> Windows Vista Ultimate and XP Home (dual-boot)
> AMD Athlon 64 X2 4200+
> Asus M2N-E
> Mushkin PC2 5300 667 - 3 gigs
> EVGA GeForce 7600 GT KO
> Antec NS 430 Watt
> WD 250 gig SATA II x2
>
> Problem:
> Most of the time when I bootup I get a BSOD with the following message:
>
>

Quote:

"The BIOS in this sytem is not fully ACPI compliant. Please contact > your sysem vendor for an updaed BIOS." > > STOP 0x000000A5 (0x00000011, 0x00000006, 0x00000000, 0x00000000)

> I removed the CMOS battery and reset the BIOS with the mb jumper. No
> change. I just now tried "Last known good configuration" for the second
> time today. No change.
>
> I following the insructions in a MSKB article,
> http://support.microsoft.com/kb/831691, that dealt with this error that
> recommended removing the "hiberfil.sys" file, but I wasn't able to delete
> it. When I tried to delete it I got an error message saying "File not
> found"??? But it is definitely there.
>
> I wondered if the same anomalies I'm seeing in Vista also would be in XP.
> So, I tried booting into XP (dual-boot) system and the bootup hung and the
> bootscreen logo. So, I can't get into XP to find out. I then used Vista
> BootPro 3.3 to restore a saved backup but no change. I pulled the mb
> battery and reset the BIOS with the mb jumper, no change. I have run 2
> memory diagnostic tests both with no errors. I have run WD's "Data
> Lifeguard Diagnostic" utility and all passed with flying colors. I have
> tried booting into "Last known good configuration", but again, no change.
> And I decided to restore a week-old True Image backup, using the Boot
> Disk, but clicking "Next" on the first screen of the Restore feature, the
> system hung and I got one loud, long beep. I had to hard reboot to escape.
> I've flashed the BIOS with 3 different versions, no change. I've also
> tried System Restore with 3 different restore points
>
> I booted with the Vista DVD and ran the Boot repair/check and no errors.
> Also ran Vista/Microsoft RAM diagnostic even though memtest86 said no
> errors and Microsoft's test was good too. I ran WD's "Data Lifeguard
> Diagnostic" utility, both Quick and Advanced with no errors or problems. I
> removed the last two "Hot Fixes", uninstalled Logitech Mouse drivers,
> disabled the Sidebar, etc. No change.
>
> The only real change I have made is to install a new Samsung 931c LCD
> monitor. And, I even disconnected that and tried an old CRT monitor out of
> desperation.... no change. I am running the latest Nvidia drivers v.
> 162.66 and reverted back to an earlier version 158.44 and no change.
> Another very strange anomaly is after the system boots into Windows Vista,
> if I click on the Start Orb to open the Start Menu, a very long line of
> "+" symbols fills the field. After about 30 seconds the same Search
> results are displayed above. I can use "Ctrl + a" to select all the "+"
> signs and delete them which then reverts the Start Menu to the way it
> should be. These same "+" signs will appear in the "Instant Search" box of
> Windows Explorer if I open that first.
>

Charlie--

While it's well known that OEM manufacturers ship cheap lower watt power
supplies as stabdard procedure, I'd doubt very seriously that this problem
is because that boxes 430Watt PSU won't cut it. Antec would confirm it's
enough, and unless the Video Card or other addition requires it, many
smaller PSUs run Vista very well with similar CPUs.

CH

"Charlie Tame" <> wrote in message
news:u$...
> Hapkido wrote:
>> I'm needing a genuine "guru" to help resolve a serious problem. Hopefully
>> someone here is up for the challenge. The following is long but perhaps
>> necessary to provide information which would most likely be asked for
>> anyway. The system is just short of a year old and has been working
>> perfectly up until yesterday.
>>
>> System Specs:
>> Windows Vista Ultimate and XP Home (dual-boot)
>> AMD Athlon 64 X2 4200+
>> Asus M2N-E
>> Mushkin PC2 5300 667 - 3 gigs
>> EVGA GeForce 7600 GT KO
>> Antec NS 430 Watt
>> WD 250 gig SATA II x2
>>
>> Problem:
>> Most of the time when I bootup I get a BSOD with the following message:
>>
>>

Quote:

"The BIOS in this sytem is not fully ACPI compliant. Please >> contact your sysem vendor for an updaed BIOS." >> >> STOP 0x000000A5 (0x00000011, 0x00000006, 0x00000000, 0x00000000)

>> I removed the CMOS battery and reset the BIOS with the mb jumper. No
>> change. I just now tried "Last known good configuration" for the second
>> time today. No change.
>>
>> I following the insructions in a MSKB article,
>> http://support.microsoft.com/kb/831691, that dealt with this error that
>> recommended removing the "hiberfil.sys" file, but I wasn't able to delete
>> it. When I tried to delete it I got an error message saying "File not
>> found"??? But it is definitely there.
>>
>> I wondered if the same anomalies I'm seeing in Vista also would be in XP.
>> So, I tried booting into XP (dual-boot) system and the bootup hung and
>> the bootscreen logo. So, I can't get into XP to find out. I then used
>> Vista BootPro 3.3 to restore a saved backup but no change. I pulled the
>> mb battery and reset the BIOS with the mb jumper, no change. I have run 2
>> memory diagnostic tests both with no errors. I have run WD's "Data
>> Lifeguard Diagnostic" utility and all passed with flying colors. I have
>> tried booting into "Last known good configuration", but again, no change.
>> And I decided to restore a week-old True Image backup, using the Boot
>> Disk, but clicking "Next" on the first screen of the Restore feature, the
>> system hung and I got one loud, long beep. I had to hard reboot to
>> escape. I've flashed the BIOS with 3 different versions, no change. I've
>> also tried System Restore with 3 different restore points
>>
>> I booted with the Vista DVD and ran the Boot repair/check and no errors.
>> Also ran Vista/Microsoft RAM diagnostic even though memtest86 said no
>> errors and Microsoft's test was good too. I ran WD's "Data Lifeguard
>> Diagnostic" utility, both Quick and Advanced with no errors or problems.
>> I removed the last two "Hot Fixes", uninstalled Logitech Mouse drivers,
>> disabled the Sidebar, etc. No change.
>>
>> The only real change I have made is to install a new Samsung 931c LCD
>> monitor. And, I even disconnected that and tried an old CRT monitor out
>> of desperation.... no change. I am running the latest Nvidia drivers v.
>> 162.66 and reverted back to an earlier version 158.44 and no change.
>> Another very strange anomaly is after the system boots into Windows
>> Vista, if I click on the Start Orb to open the Start Menu, a very long
>> line of "+" symbols fills the field. After about 30 seconds the same
>> Search results are displayed above. I can use "Ctrl + a" to select all
>> the "+" signs and delete them which then reverts the Start Menu to the
>> way it should be. These same "+" signs will appear in the "Instant
>> Search" box of Windows Explorer if I open that first.
>>
>
>
> I have the same machine almost and it's been faultless - and since XP is
> also having trouble it is unlikely a Vista problem or any OS problem. That
> MS is power hungry IMHO judging by the heat coming off that big heatsink
> tube and with the 7600 SLI card mine gets pretty warm.
>
> I wonder if your 450 watt PSU is big enough and whether it's on the way
> out. If this problem just recently started it may be worth a try. My
> biggest machine has 1000 Watt
>
> Where do you live? It's been damned hot in Iowa recently and if, like me,
> you prefer to leave machines running than risk thermal shock by keep
> turning them off then maybe a bigger PSU would work out a cheaper
> diagnostic option.
>
> Also we had a lot of thunderstorms and of course that brings with it power
> glitches.

"Hapkido" <> wrote in message
news:...
> I'm needing a genuine "guru" to help resolve a serious problem. Hopefully
> someone here is up for the challenge. The following is long but perhaps
> necessary to provide information which would most likely be asked for
> anyway. The system is just short of a year old and has been working
> perfectly up until yesterday.
>
> System Specs:
> Windows Vista Ultimate and XP Home (dual-boot)
> AMD Athlon 64 X2 4200+
> Asus M2N-E
> Mushkin PC2 5300 667 - 3 gigs
> EVGA GeForce 7600 GT KO
> Antec NS 430 Watt
> WD 250 gig SATA II x2
>
> Problem:
> Most of the time when I bootup I get a BSOD with the following message:
>
>

Quote:

"The BIOS in this sytem is not fully ACPI compliant. Please contact > your sysem vendor for an updaed BIOS." > > STOP 0x000000A5 (0x00000011, 0x00000006, 0x00000000, 0x00000000)

> I removed the CMOS battery and reset the BIOS with the mb jumper. No
change.
> I just now tried "Last known good configuration" for the second time
today.
> No change.
>
> I following the insructions in a MSKB article,
> http://support.microsoft.com/kb/831691, that dealt with this error that
> recommended removing the "hiberfil.sys" file, but I wasn't able to delete
> it. When I tried to delete it I got an error message saying "File not
> found"??? But it is definitely there.
>
>


<snip>

First off, you cannot simply delete your hiberfil.sys

you need to turn off hyberantion (from in the control panel)


I'd do so from withing both operating systems.

Even though you have reflashed your bios...I'd still have one more look
everywhere you can possibly look
(see advanced settings etc) to see if there is anything having to do with
ACPI that you might have missed.

Next try things such as underclocking the RAM and/or CPU.

I've often worked around some very odd glitches by slightly underclocking

Without jumping the gun here, I believe you have found the problem. I
switched keyboards; removing the MS Natural Ergonomic 4000 (USB 2.0) and
going back to my previous MS Natural Elite (PS-2). I've been able to reboot
several times with no BSOD, no "+" signs in the "Search Now" field nor
anywhere else where they were appearing.... etc. In short, everything seems
to be back to normal and working 100%. I can't believe it..... roflol.

So now, how can I determine whether it is a faulty keyboard or the keyboard
controller has a problem? They keyboard can be tested by trying another
similar one and seeing if the problem resurfaces. But if it is the keyboard
controller wouldn't that have the same effect on any/all keyboards?

THANKS!! :~)


"dzomlija" <> wrote in message
news:...
>
> Have to triend turning off all power management features in your BIOS?
>
> As far as the + signs go, what happens when you open notepad, or any
> other text editor, like word?. Do the +++++++'s begin to appear there
> also? That could be indicative of a bad keyboard/keyboard controller, in
> which case you need to check motherboard drivers.
>
> If you're using a USB keyboard, try replacing that with a PS/2 based
> keyboard, or if not possible, then enable Legacy USB support in your
> BIOS also.
>
>
> --
> dzomlija
>
> ____________________________________
> Peter Alexander Dzomlija
> Do you hear, huh? The Alpha and The Omega? Death and Rebirth? And as
> you die, so shall I be Reborn...

Glad to be of service.

I Think the point was, if another keyboard resulted in the same errors,
then the Keyboard Controller would be at fault. But the problem has gone
away, so it's a safe bet to assume that the keyboard itself was at
fault.

What does the the "bad" keyboard do on another machine?


--
dzomlija

____________________________________
Peter Alexander Dzomlija
Do you hear, huh? The Alpha and The Omega? Death and Rebirth? And as
you die, so shall I be Reborn...