RC2 Install Hangs @ Completing Installation

RC1 installed OK on this machine but had a note to update Linksys NIC card
driver with ? in Device Mgr. When I did a clean install with RC2 - several
attempts all froze after reaching the Completing Installation step - I let it
sit for 6 hours and but did not budge. After removing the Linksys NIC and
reinstalling it came right up. I then downloaded and installed the Linksys
updated driver, shut down, installed NIC, restarted - came right up.

RC2 runs much better than RC1 and seems significantly better.

I would suggest that folks remove all unneccessary plug-ins (PCI cards)
before installing RC2, then add hardware 1 at a time until all are up and
clean in Device Manager.

----------------
This post is a suggestion for Microsoft, and Microsoft responds to the
suggestions with the most votes. To vote for this suggestion, click the "I
Agree" button in the message pane. If you do not see the button, follow this
link to open the suggestion in the Microsoft Web-based Newsreader and then
click "I Agree" in the message pane.

http://windowshelp.microsoft.com/com...allation_setup

Now, the RC2 install, I will say, took a little longer than RC1. I can only
imagine it has to do with the addition of different programs and scripts for
bug repairs. "Completing Installation" took the longest of all to complete. I
would venture to say it took almost 20 minutes at that stage. I don't think
it was a hang-up though, because after it had time to "process" itself, it
went along it's merry way.
Performance wise, I can't say anything bad about RC2. it is just rock in and
rollin on my system.

"RobertLane" wrote:

> RC1 installed OK on this machine but had a note to update Linksys NIC card
> driver with ? in Device Mgr. When I did a clean install with RC2 - several
> attempts all froze after reaching the Completing Installation step - I let it
> sit for 6 hours and but did not budge. After removing the Linksys NIC and
> reinstalling it came right up. I then downloaded and installed the Linksys
> updated driver, shut down, installed NIC, restarted - came right up.
>
> RC2 runs much better than RC1 and seems significantly better.
>
> I would suggest that folks remove all unneccessary plug-ins (PCI cards)
> before installing RC2, then add hardware 1 at a time until all are up and
> clean in Device Manager.
>
> ----------------
> This post is a suggestion for Microsoft, and Microsoft responds to the
> suggestions with the most votes. To vote for this suggestion, click the "I
> Agree" button in the message pane. If you do not see the button, follow this
> link to open the suggestion in the Microsoft Web-based Newsreader and then
> click "I Agree" in the message pane.
>
> http://windowshelp.microsoft.com/com...allation_setup

I did an update from 5728 to 5744 on both x86 and x64
without removing any peripherals and did not encounter any
problems. Your suggestion should not be necessary.

RobertLane wrote:
> RC1 installed OK on this machine but had a note to update Linksys NIC card
> driver with ? in Device Mgr. When I did a clean install with RC2 - several
> attempts all froze after reaching the Completing Installation step - I let it
> sit for 6 hours and but did not budge. After removing the Linksys NIC and
> reinstalling it came right up. I then downloaded and installed the Linksys
> updated driver, shut down, installed NIC, restarted - came right up.
>
> RC2 runs much better than RC1 and seems significantly better.
>
> I would suggest that folks remove all unneccessary plug-ins (PCI cards)
> before installing RC2, then add hardware 1 at a time until all are up and
> clean in Device Manager.
>
> ----------------
> This post is a suggestion for Microsoft, and Microsoft responds to the
> suggestions with the most votes. To vote for this suggestion, click the "I
> Agree" button in the message pane. If you do not see the button, follow this
> link to open the suggestion in the Microsoft Web-based Newsreader and then
> click "I Agree" in the message pane.
>
> http://windowshelp.microsoft.com/com...allation_setup

"Theo" wrote:

> I did an update from 5728 to 5744 on both x86 and x64
> without removing any peripherals and did not encounter any
> problems. Your suggestion should not be necessary.
>
> RobertLane wrote:
> > RC1 installed OK on this machine but had a note to update Linksys NIC card
> > driver with ? in Device Mgr. When I did a clean install with RC2 - several
> > attempts all froze after reaching the Completing Installation step - I let it
> > sit for 6 hours and but did not budge. After removing the Linksys NIC and
> > reinstalling it came right up. I then downloaded and installed the Linksys
> > updated driver, shut down, installed NIC, restarted - came right up.
> >
> > RC2 runs much better than RC1 and seems significantly better.
> >
> > I would suggest that folks remove all unneccessary plug-ins (PCI cards)
> > before installing RC2, then add hardware 1 at a time until all are up and
> > clean in Device Manager.
> >
> > ----------------
> > This post is a suggestion for Microsoft, and Microsoft responds to the
> > suggestions with the most votes. To vote for this suggestion, click the "I
> > Agree" button in the message pane. If you do not see the button, follow this
> > link to open the suggestion in the Microsoft Web-based Newsreader and then
> > click "I Agree" in the message pane.
> >
> > http://windowshelp.microsoft.com/com...allation_setup
>