Stop Error 0x0000007b

I'm trying to install Vista Beta 2, I have downloaded the iso file and
burned a DVD. I'm installing using Windows XP on a 20 gb logical partition
on the same drive as Windows XP (C partition). The installation goes well
until the first reboot. Then I get the following message:
A problem has been detected and windows has been shut down to prevent
damage to your computer. If this is the first time you've seen this stop
error screen, restart your computer. If the screen appears again, follow
these steps: check for viruseson your computer. Remove any newly installed
hard drives or hard drive controllers. Check your hard drive to make sure it
is properly configured and terminated. Run chdksk /F to check for hard drive
corruption, and then restart your computer.
Tech information
STOP: 0x0000007B (0x81006BB0,0x00000034, 0x00000000,0x00000000)
I have run a virus scan - no viruses found, I have run chkdsk and no
problems found, I have not installed any new hard drives or hard drive
controllers, and since Windows XP runs, I'm sure the hard drive is properly
configured and terminated (what ever that means).
My system consists of an ASUS P5VDC-Mx motherboard, a Intel Pentium D 2.66
GHz CPU, 1 kb of ram, a 160 GB SATA hard drive, and a Nvidia GeForce 6200
video card.
Any help will be appreciated.

Respectfully,
Louis LeBrun

Are you installing to a RAID array or SATA? I had the same problem w/ my
RAID setup, the Vista install won't detect ANY of the dirvers I have for it
on ANY form of media.

I ended up installing it on my IDE drive being forced to change my boot
drive in BIOS whenever I want to boot a different OS. I can't find info
anywhere on pointing the new boot loader to a different device in the system,
only ways to point to diferent patitions on the same drive.


Drew

"Louis LeBrun" wrote:

> I'm trying to install Vista Beta 2, I have downloaded the iso file and
> burned a DVD. I'm installing using Windows XP on a 20 gb logical partition
> on the same drive as Windows XP (C partition). The installation goes well
> until the first reboot. Then I get the following message:
> A problem has been detected and windows has been shut down to prevent
> damage to your computer. If this is the first time you've seen this stop
> error screen, restart your computer. If the screen appears again, follow
> these steps: check for viruseson your computer. Remove any newly installed
> hard drives or hard drive controllers. Check your hard drive to make sure it
> is properly configured and terminated. Run chdksk /F to check for hard drive
> corruption, and then restart your computer.
> Tech information
> STOP: 0x0000007B (0x81006BB0,0x00000034, 0x00000000,0x00000000)
> I have run a virus scan - no viruses found, I have run chkdsk and no
> problems found, I have not installed any new hard drives or hard drive
> controllers, and since Windows XP runs, I'm sure the hard drive is properly
> configured and terminated (what ever that means).
> My system consists of an ASUS P5VDC-Mx motherboard, a Intel Pentium D 2.66
> GHz CPU, 1 kb of ram, a 160 GB SATA hard drive, and a Nvidia GeForce 6200
> video card.
> Any help will be appreciated.
>
> Respectfully,
> Louis LeBrun
>
>
>

The 7b error can be caused by various things. One quite common is some kind
of IDE driver issue.

First I would recommend to try changing SATA settings in BIOS if possible
and see if that makes a difference.
If you happen to have spare PATA drives somewhere, try installing on one of
those too. It might use a different chip on the motherboard and thus help
avoid the 7b error.

The bios often have SATA Enchanced, legacy, compatibility, raid or such
modes.. Try one that doesn't say anything or says legacy or compatibility.


"Louis LeBrun" <> wrote in message
news:eTz%...
> I'm trying to install Vista Beta 2, I have downloaded the iso file and
> burned a DVD. I'm installing using Windows XP on a 20 gb logical partition
> on the same drive as Windows XP (C partition). The installation goes well
> until the first reboot. Then I get the following message:
> A problem has been detected and windows has been shut down to prevent
> damage to your computer. If this is the first time you've seen this stop
> error screen, restart your computer. If the screen appears again, follow
> these steps: check for viruseson your computer. Remove any newly installed
> hard drives or hard drive controllers. Check your hard drive to make sure
> it is properly configured and terminated. Run chdksk /F to check for hard
> drive corruption, and then restart your computer.
> Tech information
> STOP: 0x0000007B (0x81006BB0,0x00000034, 0x00000000,0x00000000)
> I have run a virus scan - no viruses found, I have run chkdsk and no
> problems found, I have not installed any new hard drives or hard drive
> controllers, and since Windows XP runs, I'm sure the hard drive is
> properly configured and terminated (what ever that means).
> My system consists of an ASUS P5VDC-Mx motherboard, a Intel Pentium D 2.66
> GHz CPU, 1 kb of ram, a 160 GB SATA hard drive, and a Nvidia GeForce 6200
> video card.
> Any help will be appreciated.
>
> Respectfully,
> Louis LeBrun
>

I'm installing SATA. I have no RAID array.
I tried installing Vista on as second IDE hard drive and got the same
results. (I did not remove the SATA drive, I just added a second drive.)

Lou

"DrDrew" <> wrote in message
news:F14C7639-6607-4EE9-ACFA-...
> Are you installing to a RAID array or SATA? I had the same problem w/ my
> RAID setup, the Vista install won't detect ANY of the dirvers I have for
> it
> on ANY form of media.
>
> I ended up installing it on my IDE drive being forced to change my boot
> drive in BIOS whenever I want to boot a different OS. I can't find info
> anywhere on pointing the new boot loader to a different device in the
> system,
> only ways to point to diferent patitions on the same drive.
>
>
> Drew
>
<Snip>

There is no options in the BIOS to change any SATA settings. I have added a
second IDE hard drive and got the same results.

Lou

"droid" <> wrote in message
news:3B5DD614-7C68-48A0-B0E3-...
> The 7b error can be caused by various things. One quite common is some
> kind of IDE driver issue.
>
> First I would recommend to try changing SATA settings in BIOS if possible
> and see if that makes a difference.
> If you happen to have spare PATA drives somewhere, try installing on one
> of those too. It might use a different chip on the motherboard and thus
> help avoid the 7b error.
>
> The bios often have SATA Enchanced, legacy, compatibility, raid or such
> modes.. Try one that doesn't say anything or says legacy or compatibility.
>
>
<Snip>

If XP still works, run pci32.exe >output.txt and paste its output to here.

http://members.net-tech.com.au/dft0802/downloads.htm

It's not immediate remedy but might help fixing the issue.. in the long
run..
Also google -> beta client (http://go.microsoft.com/fwlink/?LinkId=43655)
The first link should be Microsoft link. It needs .NET but I think it will
be installed if you try to run it without it..
When you report a bug with it, it'll include hardware info to MS. The more
people reporting this error the likely they'll do something.


"Louis LeBrun" <> wrote in message
news:...
> There is no options in the BIOS to change any SATA settings. I have added
> a second IDE hard drive and got the same results.
>
> Lou
>
> "droid" <> wrote in message
> news:3B5DD614-7C68-48A0-B0E3-...
>> The 7b error can be caused by various things. One quite common is some
>> kind of IDE driver issue.
>>
>> First I would recommend to try changing SATA settings in BIOS if possible
>> and see if that makes a difference.
>> If you happen to have spare PATA drives somewhere, try installing on one
>> of those too. It might use a different chip on the motherboard and thus
>> help avoid the 7b error.
>>
>> The bios often have SATA Enchanced, legacy, compatibility, raid or such
>> modes.. Try one that doesn't say anything or says legacy or
>> compatibility.
>>
>>
> <Snip>
>

Quite a few unknown devices..

You did download the updated
http://members.net-tech.com.au/dft08...ds/pcidevs.txt
file before running? I forgot to mention about that.. :-(

Also more information may come with -R switch since it looks like you have 2
pci express root thingies..
This is what it says on the download page:

"- Keeping up with modern hardware - with full PCI Express and multiple
root-bus support via the -R option, PCI32 outperforms older tools tenfold"

So it may be needed to use the -R to find out devices under the PCIe roots
.... Give it a try if you like and see if there's more output this way.


"Louis LeBrun" <> wrote in message
news:...
> The output of pci32 is attached.
>
> Lou
>
> "droid" <> wrote in message
> news:AC6A9153-C3F6-457D-AAB4-...
>> If XP still works, run pci32.exe >output.txt and paste its output to
>> here.
>>
>> http://members.net-tech.com.au/dft0802/downloads.htm
>>
>> It's not immediate remedy but might help fixing the issue.. in the long
>> run..
>> Also google -> beta client (http://go.microsoft.com/fwlink/?LinkId=43655)
>> The first link should be Microsoft link. It needs .NET but I think it
>> will
>> be installed if you try to run it without it..
>> When you report a bug with it, it'll include hardware info to MS. The
>> more
>> people reporting this error the likely they'll do something.
>>
>>
> <Snip>
>
>
>

Hi all,

Just wanted to share my experiences with you, in hopes of finding a
resolution to this most annoying prblem...

I too get the BSOD after first reboot in Vista install. It seems that the
general concensus is that 7B is Vista not liking something on the IDE bus.
So, I unplugged the ONLY IDE drive from the mobo (Pioneer DVR-109), and
disabled all IDE channels in the BIOS. I then rebooted, and deleted all the
files that Vista had written to my XP partition (C: ), copied the Vista DVD
to the partition I want to install it on (D: ), and ran setup from the hard
drive, which by the way, is 2 WD 740 GD's in RAID 0 on Nvidia SATA ports 3
and 4. So there are NO IDE devices AT ALL.

And guess what? Still got the 7B stop error.

I tried booting in safe mode, to finish the install, I disabled driver sig
checking, enabled boot logging, none having the desired effect of allowing
Vista to finish installing.

I will attach pci32's report in its entirety, in hopes that someone will see
what I have been unable to see.

Report-Date = 23-06-2006 (D-M-Y)


PC-Model =


=== F u l l R e p o r t ================================================



Bus 0 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Eh nForce4 Memory Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Memory, type Other
New Capabilities List Present:
HyperTransport Capability
SubType : Slave/Primary Interface
Base UnitID : 0
UnitID Count : 15
HyperTransport Capability
SubType : MSI Mapping

Bus 0 (PCI Express), Device Number 1, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0050h nForce4 PCI to ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp

Bus 0 (PCI Express), Device Number 1, Device Function 1
Vendor 10DEh Nvidia Corp
Device 0052h nForce4 SMBus
Command 0001h (I/O Access)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type SMBus Controller
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 0000FC00h
Address 4 is an I/O Port : 00001C00h
Address 5 is an I/O Port : 00001C40h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ah nForce4 USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (OHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02F000h
System IRQ 22, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 1
Vendor 10DEh Nvidia Corp
Device 005Bh nForce4 USB 2.0 Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FEB00000h
System IRQ 20, INT# B
New Capabilities List Present:
USB 2.0 EHCI Debug Port Capability
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 6, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0053h nForce4 Parallel ATA Controller
Command 0005h (I/O Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 4 is an I/O Port : 0000F000h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 7, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0054h nForce4 Serial ATA Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is in native mode at Addresses 0 & 1
Secondary Channel is in native mode at Addresses 2 & 3
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 000009F0h
Address 1 is an I/O Port : 00000BF0h
Address 2 is an I/O Port : 00000970h
Address 3 is an I/O Port : 00000B70h
Address 4 is an I/O Port : 0000DC00h
Address 5 is a Memory Address (anywhere in 0-4Gb) : FE02D000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 9, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ch nForce4 PCI Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A2h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 0204h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master
Abort, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : None
Prefetchable Memory Range Passed to Secondary Bus : None

Bus 0 (PCI Express), Device Number 10, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0057h nForce4 Ethernet Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 01h, Maximum Bus Latency 14h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02C000h
Address 1 is an I/O Port : 0000D800h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently enabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 11, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 2
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000B000h to 0000BFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDD00000h to FDDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDC00000h to
00000000FDCFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Fatal Error Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : xReserved
Link Port Number : 3
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Link Training Error Reported!!
Slot Capabilities :
Slot Power Limit Value : 6.000 Watts
Physical slot Number 1

Bus 0 (PCI Express), Device Number 12, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 3, Subordinate Bus Number 3
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000A000h to 0000AFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDB00000h to FDBFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDA00000h to
00000000FDAFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x4
Link Port Number : 2
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Slot Capabilities :
Slot Power Limit Value : 4.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 13, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 4, Subordinate Bus Number 4
Secondary Bus Command 000Ch (ISA mapping, VGA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00009000h to 00009FFFh (32-bit)
Memory Range Passed to Secondary Bus : FA000000h to FCFFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000D0000000h to
00000000DFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 2.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 14, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 5, Subordinate Bus Number 5
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00008000h to 00008FFFh (32-bit)
Memory Range Passed to Secondary Bus : F7000000h to F9FFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000C0000000h to
00000000CFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 0.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 24, Device Function 0
Vendor 1022h Advanced Micro Devices (AMD)
Device 1100h Athlon 64 / Opteron HyperTransport Technology Configuration
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
New Capabilities List Present:
HyperTransport Capability
SubType : Host/Secondary Interface

Bus 0 (PCI Express), Device Number 24, Device Function 1
Vendor 1022h Advanced Micro Devices (AMD)
Device 1101h Athlon 64 / Opteron Address Map
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 2
Vendor 1022h Advanced Micro Devices (AMD)
Device 1102h Athlon 64 / Opteron DRAM Controller
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 3
Vendor 1022h Advanced Micro Devices (AMD)
Device 1103h Athlon 64 / Opteron Miscellaneous Control
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 1 (PCI), Device Number 7, Device Function 0
Vendor 13F6h C-Media Electronics Inc
Device 0111h CMI8738/C3DX PCI Audio Device
Command 0085h (I/O Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 10h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 02h, Maximum Bus Latency 18h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 3741584Dh Unknown
Subsystem Vendor 584Dh Unknown
Address 0 is an I/O Port : 0000CC00h
System IRQ 19, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 4 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : FA000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
D0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : FB000000h
Address 5 is an I/O Port : 00009C00h
System IRQ 19, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8

Bus 5 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0006h (Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : F9000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
C0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : F8000000h
Address 5 is an I/O Port : 00008C80h
System IRQ 18, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8


IRQ Summary: IRQs 10,14,15,18,19,20,21,22,23 are used by PCI devices
Shared IRQs: IRQ 19 is shared by 2 PCI Devices

IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...


PCI Busses, Devices and Device Functions Tree

--Bus 0 (PCI Express)
|__Device 00h 10DEh:005Eh Other Memory
|__Device 01h
| |__Function 0 10DEh:0050h PCI to ISA Bridge
| |__Function 1 10DEh:0052h SMBus Controller Serial
|__Device 02h
| |__Function 0 10DEh:005Ah USB (OHCI) Serial
| |__Function 1 10DEh:005Bh USB 2.0 (EHCI) Serial
|__Device 06h 10DEh:0053h IDE (ATA) Storage
|__Device 07h 10DEh:0054h IDE (ATA) Storage
|__Device 09h 10DEh:005Ch PCI to PCI (Subtractive Decode) Bridge
> Bus 1
|__Device 0Ah 10DEh:0057h PCI to Other Bridge
|__Device 0Bh 10DEh:005Dh PCI to PCI Bridge > Bus 2
|__Device 0Ch 10DEh:005Dh PCI to PCI Bridge > Bus 3
|__Device 0Dh 10DEh:005Dh PCI to PCI Bridge > Bus 4
|__Device 0Eh 10DEh:005Dh PCI to PCI Bridge > Bus 5
|__Device 18h
|__Function 0 1022h:1100h PCI to HOST Bridge
|__Function 1 1022h:1101h PCI to HOST Bridge
|__Function 2 1022h:1102h PCI to HOST Bridge
|__Function 3 1022h:1103h PCI to HOST Bridge

--Bus 1 (PCI)
|__Device 07h 13F6h:0111h Audio Multimedia

--Bus 2
|__No Devices Currently Present

--Bus 3
|__No Devices Currently Present

--Bus 4 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

--Bus 5 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

A total of 20 Devices Found

I have been trying to install Vista for 3 days now. I realize that it is
BETA, but FFS, this is rediculous. I am by no means a computer expert, but I
know how to install an OS. IT should'nt be this much hassle and fuss.

Thanks for all your input, It is greatly appreciated.

Victor

************************************************** ********

"droid" wrote:

> Quite a few unknown devices..
>
> You did download the updated
> http://members.net-tech.com.au/dft08...ds/pcidevs.txt
> file before running? I forgot to mention about that.. :-(
>
> Also more information may come with -R switch since it looks like you have 2
> pci express root thingies..
> This is what it says on the download page:
>
> "- Keeping up with modern hardware - with full PCI Express and multiple
> root-bus support via the -R option, PCI32 outperforms older tools tenfold"
>
> So it may be needed to use the -R to find out devices under the PCIe roots
> .... Give it a try if you like and see if there's more output this way.
>
>
> "Louis LeBrun" <> wrote in message
> news:...
> > The output of pci32 is attached.
> >
> > Lou
> >
> > "droid" <> wrote in message
> > news:AC6A9153-C3F6-457D-AAB4-...
> >> If XP still works, run pci32.exe >output.txt and paste its output to
> >> here.
> >>
> >> http://members.net-tech.com.au/dft0802/downloads.htm
> >>
> >> It's not immediate remedy but might help fixing the issue.. in the long
> >> run..
> >> Also google -> beta client (http://go.microsoft.com/fwlink/?LinkId=43655)
> >> The first link should be Microsoft link. It needs .NET but I think it
> >> will
> >> be installed if you try to run it without it..
> >> When you report a bug with it, it'll include hardware info to MS. The
> >> more
> >> people reporting this error the likely they'll do something.
> >>
> >>
> > <Snip>
> >
> >
> >
>
>

Hi all,

Just wanted to share my experiences with you, in hopes of finding a
resolution to this most annoying prblem...

I too get the BSOD after first reboot in Vista install. It seems that the
general concensus is that 7B is Vista not liking something on the IDE bus.
So, I unplugged the ONLY IDE drive from the mobo (Pioneer DVR-109), and
disabled all IDE channels in the BIOS. I then rebooted, and deleted all the
files that Vista had written to my XP partition (C: ), copied the Vista DVD
to the partition I want to install it on (D: ), and ran setup from the hard
drive, which by the way, is 2 WD 740 GD's in RAID 0 on Nvidia SATA ports 3
and 4. So there are NO IDE devices AT ALL.

And guess what? Still got the 7B stop error.

I tried booting in safe mode, to finish the install, I disabled driver sig
checking, enabled boot logging, none having the desired effect of allowing
Vista to finish installing.

I will attach pci32's report in its entirety, in hopes that someone will see
what I have been unable to see.

Report-Date = 23-06-2006 (D-M-Y)


PC-Model =


=== F u l l R e p o r t ================================================



Bus 0 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Eh nForce4 Memory Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Memory, type Other
New Capabilities List Present:
HyperTransport Capability
SubType : Slave/Primary Interface
Base UnitID : 0
UnitID Count : 15
HyperTransport Capability
SubType : MSI Mapping

Bus 0 (PCI Express), Device Number 1, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0050h nForce4 PCI to ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp

Bus 0 (PCI Express), Device Number 1, Device Function 1
Vendor 10DEh Nvidia Corp
Device 0052h nForce4 SMBus
Command 0001h (I/O Access)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type SMBus Controller
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 0000FC00h
Address 4 is an I/O Port : 00001C00h
Address 5 is an I/O Port : 00001C40h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ah nForce4 USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (OHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02F000h
System IRQ 22, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 1
Vendor 10DEh Nvidia Corp
Device 005Bh nForce4 USB 2.0 Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FEB00000h
System IRQ 20, INT# B
New Capabilities List Present:
USB 2.0 EHCI Debug Port Capability
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 6, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0053h nForce4 Parallel ATA Controller
Command 0005h (I/O Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 4 is an I/O Port : 0000F000h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 7, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0054h nForce4 Serial ATA Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is in native mode at Addresses 0 & 1
Secondary Channel is in native mode at Addresses 2 & 3
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 000009F0h
Address 1 is an I/O Port : 00000BF0h
Address 2 is an I/O Port : 00000970h
Address 3 is an I/O Port : 00000B70h
Address 4 is an I/O Port : 0000DC00h
Address 5 is a Memory Address (anywhere in 0-4Gb) : FE02D000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 9, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ch nForce4 PCI Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A2h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 0204h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master
Abort, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : None
Prefetchable Memory Range Passed to Secondary Bus : None

Bus 0 (PCI Express), Device Number 10, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0057h nForce4 Ethernet Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 01h, Maximum Bus Latency 14h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02C000h
Address 1 is an I/O Port : 0000D800h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently enabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 11, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 2
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000B000h to 0000BFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDD00000h to FDDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDC00000h to
00000000FDCFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Fatal Error Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : xReserved
Link Port Number : 3
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Link Training Error Reported!!
Slot Capabilities :
Slot Power Limit Value : 6.000 Watts
Physical slot Number 1

Bus 0 (PCI Express), Device Number 12, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 3, Subordinate Bus Number 3
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000A000h to 0000AFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDB00000h to FDBFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDA00000h to
00000000FDAFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x4
Link Port Number : 2
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Slot Capabilities :
Slot Power Limit Value : 4.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 13, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 4, Subordinate Bus Number 4
Secondary Bus Command 000Ch (ISA mapping, VGA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00009000h to 00009FFFh (32-bit)
Memory Range Passed to Secondary Bus : FA000000h to FCFFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000D0000000h to
00000000DFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 2.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 14, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 5, Subordinate Bus Number 5
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00008000h to 00008FFFh (32-bit)
Memory Range Passed to Secondary Bus : F7000000h to F9FFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000C0000000h to
00000000CFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 0.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 24, Device Function 0
Vendor 1022h Advanced Micro Devices (AMD)
Device 1100h Athlon 64 / Opteron HyperTransport Technology Configuration
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
New Capabilities List Present:
HyperTransport Capability
SubType : Host/Secondary Interface

Bus 0 (PCI Express), Device Number 24, Device Function 1
Vendor 1022h Advanced Micro Devices (AMD)
Device 1101h Athlon 64 / Opteron Address Map
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 2
Vendor 1022h Advanced Micro Devices (AMD)
Device 1102h Athlon 64 / Opteron DRAM Controller
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 3
Vendor 1022h Advanced Micro Devices (AMD)
Device 1103h Athlon 64 / Opteron Miscellaneous Control
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 1 (PCI), Device Number 7, Device Function 0
Vendor 13F6h C-Media Electronics Inc
Device 0111h CMI8738/C3DX PCI Audio Device
Command 0085h (I/O Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 10h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 02h, Maximum Bus Latency 18h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 3741584Dh Unknown
Subsystem Vendor 584Dh Unknown
Address 0 is an I/O Port : 0000CC00h
System IRQ 19, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 4 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : FA000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
D0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : FB000000h
Address 5 is an I/O Port : 00009C00h
System IRQ 19, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8

Bus 5 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0006h (Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : F9000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
C0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : F8000000h
Address 5 is an I/O Port : 00008C80h
System IRQ 18, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8


IRQ Summary: IRQs 10,14,15,18,19,20,21,22,23 are used by PCI devices
Shared IRQs: IRQ 19 is shared by 2 PCI Devices

IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...


PCI Busses, Devices and Device Functions Tree

--Bus 0 (PCI Express)
|__Device 00h 10DEh:005Eh Other Memory
|__Device 01h
| |__Function 0 10DEh:0050h PCI to ISA Bridge
| |__Function 1 10DEh:0052h SMBus Controller Serial
|__Device 02h
| |__Function 0 10DEh:005Ah USB (OHCI) Serial
| |__Function 1 10DEh:005Bh USB 2.0 (EHCI) Serial
|__Device 06h 10DEh:0053h IDE (ATA) Storage
|__Device 07h 10DEh:0054h IDE (ATA) Storage
|__Device 09h 10DEh:005Ch PCI to PCI (Subtractive Decode) Bridge
> Bus 1
|__Device 0Ah 10DEh:0057h PCI to Other Bridge
|__Device 0Bh 10DEh:005Dh PCI to PCI Bridge > Bus 2
|__Device 0Ch 10DEh:005Dh PCI to PCI Bridge > Bus 3
|__Device 0Dh 10DEh:005Dh PCI to PCI Bridge > Bus 4
|__Device 0Eh 10DEh:005Dh PCI to PCI Bridge > Bus 5
|__Device 18h
|__Function 0 1022h:1100h PCI to HOST Bridge
|__Function 1 1022h:1101h PCI to HOST Bridge
|__Function 2 1022h:1102h PCI to HOST Bridge
|__Function 3 1022h:1103h PCI to HOST Bridge

--Bus 1 (PCI)
|__Device 07h 13F6h:0111h Audio Multimedia

--Bus 2
|__No Devices Currently Present

--Bus 3
|__No Devices Currently Present

--Bus 4 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

--Bus 5 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

A total of 20 Devices Found

I have been trying to install Vista for 3 days now. I realize that it is
BETA, but FFS, this is rediculous. I am by no means a computer expert, but I
know how to install an OS. IT should'nt be this much hassle and fuss.

Thanks for all your input, It is greatly appreciated.

Victor

"droid" wrote:

> Quite a few unknown devices..
>
> You did download the updated
> http://members.net-tech.com.au/dft08...ds/pcidevs.txt
> file before running? I forgot to mention about that.. :-(
>
> Also more information may come with -R switch since it looks like you have 2
> pci express root thingies..
> This is what it says on the download page:
>
> "- Keeping up with modern hardware - with full PCI Express and multiple
> root-bus support via the -R option, PCI32 outperforms older tools tenfold"
>
> So it may be needed to use the -R to find out devices under the PCIe roots
> .... Give it a try if you like and see if there's more output this way.
>
>
> "Louis LeBrun" <> wrote in message
> news:...
> > The output of pci32 is attached.
> >
> > Lou
> >
> > "droid" <> wrote in message
> > news:AC6A9153-C3F6-457D-AAB4-...
> >> If XP still works, run pci32.exe >output.txt and paste its output to
> >> here.
> >>
> >> http://members.net-tech.com.au/dft0802/downloads.htm
> >>
> >> It's not immediate remedy but might help fixing the issue.. in the long
> >> run..
> >> Also google -> beta client (http://go.microsoft.com/fwlink/?LinkId=43655)
> >> The first link should be Microsoft link. It needs .NET but I think it
> >> will
> >> be installed if you try to run it without it..
> >> When you report a bug with it, it'll include hardware info to MS. The
> >> more
> >> people reporting this error the likely they'll do something.
> >>
> >>
> > <Snip>
> >
> >
> >
>
>

Hi all,

Just wanted to share my experiences with you, in hopes of finding a
resolution to this most annoying prblem...

I too get the BSOD after first reboot in Vista install. It seems that the
general concensus is that 7B is Vista not liking something on the IDE bus.
So, I unplugged the ONLY IDE drive from the mobo (Pioneer DVR-109), and
disabled all IDE channels in the BIOS. I then rebooted, and deleted all the
files that Vista had written to my XP partition (C: ), copied the Vista DVD
to the partition I want to install it on (D: ), and ran setup from the hard
drive, which by the way, is 2 WD 740 GD's in RAID 0 on Nvidia SATA ports 3
and 4. So there are NO IDE devices AT ALL.

And guess what? Still got the 7B stop error.

I tried booting in safe mode, to finish the install, I disabled driver sig
checking, enabled boot logging, none having the desired effect of allowing
Vista to finish installing.

I will attach pci32's report in its entirety, in hopes that someone will see
what I have been unable to see.

Report-Date = 23-06-2006 (D-M-Y)


PC-Model =


=== F u l l R e p o r t ================================================



Bus 0 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Eh nForce4 Memory Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Memory, type Other
New Capabilities List Present:
HyperTransport Capability
SubType : Slave/Primary Interface
Base UnitID : 0
UnitID Count : 15
HyperTransport Capability
SubType : MSI Mapping

Bus 0 (PCI Express), Device Number 1, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0050h nForce4 PCI to ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp

Bus 0 (PCI Express), Device Number 1, Device Function 1
Vendor 10DEh Nvidia Corp
Device 0052h nForce4 SMBus
Command 0001h (I/O Access)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type SMBus Controller
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 0000FC00h
Address 4 is an I/O Port : 00001C00h
Address 5 is an I/O Port : 00001C40h
System IRQ 10, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ah nForce4 USB Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (OHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02F000h
System IRQ 22, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 2, Device Function 1
Vendor 10DEh Nvidia Corp
Device 005Bh nForce4 USB 2.0 Controller
Command 0006h (Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 80h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Serial, type USB 2.0 (EHCI)
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FEB00000h
System IRQ 20, INT# B
New Capabilities List Present:
USB 2.0 EHCI Debug Port Capability
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 6, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0053h nForce4 Parallel ATA Controller
Command 0005h (I/O Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A2h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 4 is an I/O Port : 0000F000h
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 7, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0054h nForce4 Serial ATA Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 03h, Maximum Bus Latency 01h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE (ATA)
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is in native mode at Addresses 0 & 1
Secondary Channel is in native mode at Addresses 2 & 3
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is an I/O Port : 000009F0h
Address 1 is an I/O Port : 00000BF0h
Address 2 is an I/O Port : 00000970h
Address 3 is an I/O Port : 00000B70h
Address 4 is an I/O Port : 0000DC00h
Address 5 is a Memory Address (anywhere in 0-4Gb) : FE02D000h
System IRQ 21, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 0 (PCI Express), Device Number 9, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Ch nForce4 PCI Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00A0h (Supports 66MHz, Supports Back-To-Back Trans., Fast Timing)
Revision A2h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to PCI (Subtractive Decode)
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus Number 1
Secondary Bus Command 0204h (ISA mapping)
Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master
Abort, Medium Timing)
Secondary Bus Latency 20h
I/O Port Range Passed to Secondary Bus : None
Memory Range Passed to Secondary Bus : None
Prefetchable Memory Range Passed to Secondary Bus : None

Bus 0 (PCI Express), Device Number 10, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0057h nForce4 Ethernet Controller
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 00B0h (Has Capabilities List, Supports 66MHz, Supports Back-To-Back
Trans., Fast Timing)
Revision A3h, Header Type 00h, Bus Latency Timer 00h
Minimum Bus Grant 01h, Maximum Bus Latency 14h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other
Subsystem ID CB8410DEh Unknown
Subsystem Vendor 10DEh Nvidia Corp
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE02C000h
Address 1 is an I/O Port : 0000D800h
System IRQ 23, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently enabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)

Bus 0 (PCI Express), Device Number 11, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus Number 2
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000B000h to 0000BFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDD00000h to FDDFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDC00000h to
00000000FDCFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Fatal Error Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : xReserved
Link Port Number : 3
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Link Training Error Reported!!
Slot Capabilities :
Slot Power Limit Value : 6.000 Watts
Physical slot Number 1

Bus 0 (PCI Express), Device Number 12, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 3, Subordinate Bus Number 3
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 0000A000h to 0000AFFFh (32-bit)
Memory Range Passed to Secondary Bus : FDB00000h to FDBFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000FDA00000h to
00000000FDAFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x4
Link Port Number : 2
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x4
Slot Capabilities :
Slot Power Limit Value : 4.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 13, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 4, Subordinate Bus Number 4
Secondary Bus Command 000Ch (ISA mapping, VGA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00009000h to 00009FFFh (32-bit)
Memory Range Passed to Secondary Bus : FA000000h to FCFFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000D0000000h to
00000000DFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 2.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 14, Device Function 0
Vendor 10DEh Nvidia Corp
Device 005Dh nForce4 PCI Express Bridge
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A3h, Header Type 01h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Bridge, type PCI to PCI
PCI Bridge Information:
Primary Bus Number 0, Secondary Bus Number 5, Subordinate Bus Number 5
Secondary Bus Command 0004h (ISA mapping)
Secondary Bus Status 0000h
Secondary Bus Latency 00h
I/O Port Range Passed to Secondary Bus : 00008000h to 00008FFFh (32-bit)
Memory Range Passed to Secondary Bus : F7000000h to F9FFFFFFh
Prefetchable Memory Range Passed to Secondary Bus : 00000000C0000000h to
00000000CFFFFFFFh
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
Current Power State : D0 (Device operational, no power saving)
3.3v AUX Current required : 0mA (Self powered)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
HyperTransport Capability
SubType : MSI Mapping
PCI Express Capability, Version 1
Device/Port Type :
Root port of PCI Express Root Complex
Port Type :
Port is an Expansion Slot
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x8
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8
Slot Capabilities :
Slot Power Limit Value : 0.000 Watts
Physical slot Number 0

Bus 0 (PCI Express), Device Number 24, Device Function 0
Vendor 1022h Advanced Micro Devices (AMD)
Device 1100h Athlon 64 / Opteron HyperTransport Technology Configuration
Command 0000h (Bus Access Disabled!!)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST
New Capabilities List Present:
HyperTransport Capability
SubType : Host/Secondary Interface

Bus 0 (PCI Express), Device Number 24, Device Function 1
Vendor 1022h Advanced Micro Devices (AMD)
Device 1101h Athlon 64 / Opteron Address Map
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 2
Vendor 1022h Advanced Micro Devices (AMD)
Device 1102h Athlon 64 / Opteron DRAM Controller
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 0 (PCI Express), Device Number 24, Device Function 3
Vendor 1022h Advanced Micro Devices (AMD)
Device 1103h Athlon 64 / Opteron Miscellaneous Control
Command 0000h (Bus Access Disabled!!)
Status 0000h
Revision 00h, Header Type 80h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Bus 1 (PCI), Device Number 7, Device Function 0
Vendor 13F6h C-Media Electronics Inc
Device 0111h CMI8738/C3DX PCI Audio Device
Command 0085h (I/O Access, BusMaster, Wait Cycles)
Status 0210h (Has Capabilities List, Medium Timing)
Revision 10h, Header Type 00h, Bus Latency Timer 20h
Minimum Bus Grant 02h, Maximum Bus Latency 18h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 3741584Dh Unknown
Subsystem Vendor 584Dh Unknown
Address 0 is an I/O Port : 0000CC00h
System IRQ 19, INT# A
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)

Bus 4 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0007h (I/O Access, Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : FA000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
D0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : FB000000h
Address 5 is an I/O Port : 00009C00h
System IRQ 19, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 1
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8

Bus 5 (PCI Express), Device Number 0, Device Function 0
Vendor 10DEh Nvidia Corp
Device 0091h GeForce 7800 GTX
Command 0006h (Memory Access, BusMaster)
Status 0010h (Has Capabilities List, Fast Timing)
Revision A1h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
PCI Class Display, type VGA
Address 0 is a Memory Address (anywhere in 0-4Gb) : F9000000h
Address 1 is a Memory Address (anywhere in 64-bit space, Prefetchable) :
C0000000h
Address 3 is a Memory Address (anywhere in 64-bit space) : F8000000h
Address 5 is an I/O Port : 00008C80h
System IRQ 18, INT# A
Expansion ROM of 128Kb decoded by this card (Currently disabled)
New Capabilities List Present:
Power Management Capability, Version 1.1
Does not support low power State D1 or D2
Does not support PME# signalling
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 1
Device/Port Type :
PCI Express Endpoint Device
Device Capabilities :
Device Control :
Unsupported Request Severity is Fatal
Device Status :
Non-Fatal Error Detected
Unsupported Request Detected
Link Capabilities :
Maximum Link Speed : 2.5Gb/s
Maximum Link Width : x16
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link Speed : 2.5Gb/s
Current Link Width : x8


IRQ Summary: IRQs 10,14,15,18,19,20,21,22,23 are used by PCI devices
Shared IRQs: IRQ 19 is shared by 2 PCI Devices

IRQ control is currently managed by the system APIC controller - IRQ info is
not actual hardware settings...


PCI Busses, Devices and Device Functions Tree

--Bus 0 (PCI Express)
|__Device 00h 10DEh:005Eh Other Memory
|__Device 01h
| |__Function 0 10DEh:0050h PCI to ISA Bridge
| |__Function 1 10DEh:0052h SMBus Controller Serial
|__Device 02h
| |__Function 0 10DEh:005Ah USB (OHCI) Serial
| |__Function 1 10DEh:005Bh USB 2.0 (EHCI) Serial
|__Device 06h 10DEh:0053h IDE (ATA) Storage
|__Device 07h 10DEh:0054h IDE (ATA) Storage
|__Device 09h 10DEh:005Ch PCI to PCI (Subtractive Decode) Bridge
> Bus 1
|__Device 0Ah 10DEh:0057h PCI to Other Bridge
|__Device 0Bh 10DEh:005Dh PCI to PCI Bridge > Bus 2
|__Device 0Ch 10DEh:005Dh PCI to PCI Bridge > Bus 3
|__Device 0Dh 10DEh:005Dh PCI to PCI Bridge > Bus 4
|__Device 0Eh 10DEh:005Dh PCI to PCI Bridge > Bus 5
|__Device 18h
|__Function 0 1022h:1100h PCI to HOST Bridge
|__Function 1 1022h:1101h PCI to HOST Bridge
|__Function 2 1022h:1102h PCI to HOST Bridge
|__Function 3 1022h:1103h PCI to HOST Bridge

--Bus 1 (PCI)
|__Device 07h 13F6h:0111h Audio Multimedia

--Bus 2
|__No Devices Currently Present

--Bus 3
|__No Devices Currently Present

--Bus 4 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

--Bus 5 (PCI Express)
|__Device 00h 10DEh:0091h VGA Display

A total of 20 Devices Found

I have been trying to install Vista for 3 days now. I realize that it is
BETA, but FFS, this is rediculous. I am by no means a computer expert, but I
know how to install an OS. IT should'nt be this much hassle and fuss.

Thanks for all your input, It is greatly appreciated.

Victor