Help - setup file share between WinXP and Vista on a home network

Discussion in 'Windows Vista Networking' started by User66, Mar 28, 2010.

  1. User66

    User66 Guest

    It has been years, we have been transferring files between our home PCs and
    Laptops in our home network. But as we updated our Laptop with Vista SP1 &
    SP2, the network has become a one way only. We can transfer files to the
    rest of the network PCs, but the Vista Laptop does not let us in. We do see
    it listed in our network.

    We had to re-format the laptop drive and as we loaded the Vista back again,
    we were able to transfer files two way, but as the SP1 and SP2 update was
    loaded, file transfer has become one way only. Did go through the setup on
    the Laptop drive as we did before. What are we missing in SP1 & SP2

    Appreciate help.
    User66, Mar 28, 2010
    1. Advertisements

  2. Hi
    Make sure that the Software Firewall on each computer allows free local
    traffic. If you use 3rd party Firewall On, Vista/XP Native Firewall should
    be Off, and the active Firewall has to adjusted to your Network IP numbers
    on what is some time called the Trusted Zone (consult your 3rd Party
    Firewall instructions.
    General example,
    Windows 7 Work Network,
    Vista File and Printer Sharing-
    Windows XP File Sharing -;en-us;304040
    Printer Sharing
    XP -
    Windows Native Firewall setting for Sharing
    XP -
    Windows XP patch for Sharing with Vista (Not need for XP-SP3) -
    Sharing between Windows XP and Mac -
    When done hard reboot all network computers and the Router.
    Jack (MS, MVP-Networking).
    Jack [MVP-Networking], Mar 28, 2010
    1. Advertisements

  3. User66

    User66 Guest

    Hello Jack,

    Thank you so much for the reply. Although I am used to with a two way firewall, such as Zone Alarm,
    etc., but because of Vista file sharing problem, have not loaded any other firewall, except the
    built-in Vista's own firewall. Wish it was a two-way firewall or is it?

    Anyhow, we have tried just about everything, but Vista does not open the laptop for file transfer.
    We did set the laptop IP address and the gateway common address etc. properly. As I said, it did
    work until the SP1 update was loaded.

    We have tried several times by reformatting the laptop and reloading the Vista, and it does the
    same. Within the home network, the laptop can transfer files to the other PCs but the other PCs
    cannot, and the problem starts after loading Vista SP1. The Laptop name shows up on the network but
    cannot open anything.

    Will definitely post any changes, if it happens. Thank you again for the reply.

    User66, Mar 30, 2010
  4. Hi
    Yeah Vista's Firewall is two way.
    As a interim step, try to enable and let the guest share a folder with full
    permission. Add the Guest account to the security too.
    If it works you will be able to transfer files to this folder and then do
    locally on the laptop the rest.
    Jack (MS, MVP-Networking).
    Jack [MVP-Networking], Mar 30, 2010
  5. User66

    User66 Guest

    As you know, when all else fails, we revert back to old days. We ended up
    breaking up the laptop drive into C and D drives and load WinXP Pro on
    C: drive and the Vista on the D: Drive.

    At least now we can transfer files to the laptop, while it is running WinXP and
    of-course move files out while it is running Vista.

    Went through all of your suggestions. Yes we added the Guest account with
    full permission and the second drive also (since we have two partitions in our
    laptop drive now). Under "Network and Sharing Center" everything is turned On,
    except 'Media Sharing'.

    Under 'Customize network settings', we have tried both 'Public' and 'Private'
    location types - did not make any difference. Finally left it in the 'Private' mode.

    Well, don't know what else can be done to open up in the Vista mode to make
    the laptop open to transfer files from the Network group.

    Will definitely post any other changes. Thank you so much.


    P.S. Tried both with Firewall turned ON and OFF. Did not make any difference.
    User66, Apr 5, 2010
  6. User66

    User66 Guest

    Folks, found out the problem solution. The user must have a password to log in
    in the user's laptop account. Otherwise the laptop account is visible but cannot be
    entered from the network.

    Got used to with the non password in our home network running on XP. I guess
    we have to re learn our behavior with Vista.

    Thanks for the suggestions.

    User66, Apr 5, 2010
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.